Sound devices (Dante®)
KRZN Live works with a Dante audio network through Dante Virtual Soundcard (DVS) on the central computer. In WDM mode, DVS shows each pair of Dante channels as a sound device of Windows: DVS Receive 1-2 (from the network to the computer) and DVS Transmit 1-2 (from the computer to the network). KRZN Live uses these devices like any other sound device: a Dante AVIO USB adapter, a USB mixer or a line input work the same way.
Dante® is a registered trademark of Audinate Pty Ltd.
What it does
| Use | Where | What happens |
|---|---|---|
| Record the desk | Recordings > Sources > Audio > Add a sound input | A Dante pair becomes a source of its own: recorded (AAC 256 kbit/s, 48 kHz), sent to the sites and the VPS, shown in the meters. |
| A camera with the sound of the desk | Recordings > record settings of the camera > Audio | The camera is recorded with the desk mix instead of its own microphone, in lip sync (see below). |
| An NDI input with the sound of the desk | Recordings > record settings of the NDI source > Sound | For example the program of vMix with the desk mix, in lip sync. |
| A site into the PA | Stream Paths > path > Sound out (Dante) | The sound of the site plays on a Dante pair: in Dante Controller, route DVS Transmit 1-2 of this computer to the desk. |
| The desk in the intercom | Settings > Sound devices | The desk speaks in the production call (talkback: a Dante input), and hears the call (a Dante output, for example the comms or in-ear mix). It joins the call as "Sound desk", heard by central and by the sites. |
Setup
- Install Dante Virtual Soundcard on the central computer. In its window: Audio Interface: WDM, the highest number of channels, Dante Latency: 10 ms, Network Interface: the wired port of the Dante network, then Start.
- In Dante Controller (free, from getdante.com): set this computer to 48 kHz, and make the desk the clock leader ("Preferred leader"), never DVS.
- In the Windows sound settings, for each DVS device: format 48000 Hz, enhancements off, the two exclusive mode boxes on. Never make a DVS device the default device of Windows: Windows sounds and browsers would go to the desk. The dashboard warns when one is.
- Settings > Sound devices (Dante) lists the devices. Test tone plays 1 kHz at -18 dBFS for 3 seconds on an output: use it to find the pair in Dante Controller or on the desk.
WDM or ASIO
Settings > Sound devices > Sound driver:
- Automatic (default): the Windows sound devices when Dante Virtual Soundcard is in WDM mode, else its ASIO driver. It's checked every few seconds: switching DVS from one mode to the other needs no restart of KRZN Live.
- Windows sound devices (WDM): up to 16 Dante channels (8 pairs). Other programs (vMix, OBS) can use the Dante pairs at the same time.
- ASIO: up to 64 Dante channels each way (128 with DVS Pro). Only one program can use an ASIO driver: KRZN Live holds it, so vMix and OBS can't use Dante ASIO on the same computer.
Pairs are named the same way in both modes: ASIO Out 3-4 is DVS Transmit 3-4, and ASIO In 1-2 is DVS Receive 1-2. The settings of the paths keep working when DVS is switched from one mode to the other.
In ASIO mode, everything goes through ASIO: the sound outputs, the sound-only sources, the sound of NDI inputs, the desk in the intercom and the test tone. Devices that aren't Dante pairs (a USB headset) still use Windows. Cameras keep their own sound (DirectShow can't open ASIO): give them the desk through an NDI source, or record the desk as its own source.
Lip sync
- Cameras and capture cards: the picture and the sound of the desk are recorded by the same DirectShow clock, so they stay together over hours. What remains is a fixed difference (the camera and the desk don't have the same delay): set Lip sync in milliseconds. Positive: the sound later. Negative: the sound earlier. Clap in front of the camera and adjust until the clap is heard when the hands meet.
- NDI inputs: the picture is timed by its arrival on this computer and the desk sound by when it was recorded, on the same clock. Set Lip sync the same way.
- Sound-only sources (a Dante pair alone): Delay holds the sound back, so that its recording lines up with the cameras (their picture takes longer to arrive).
- Sound out: delay holds the sound of the site back, for example so that the PA matches the picture of the site on the room screen.
How the sound out stays clean
The clock of a site and the clock of the Dante network never run at exactly the same speed: without care, the sound would click or slowly drift away. Each sound out keeps a buffer (at least 150 ms: the site is seconds late anyway) and reads it a tiny bit faster or slower (at most 0.5%, inaudible) so that it stays at the same size for hours. A limiter keeps the level below -1 dBFS. When the site stops sending, the sound fades out in 20 ms and the pair plays silence; when it comes back, it fades in. The device is opened in exclusive mode (24 bits, bit-exact): no other program can play into the Dante pair. Status > Sound (Dante) shows the level, the buffer, the speed correction and the dropouts of each one.
When a Dante pair gives no sound (DVS stopped, or without its clock), a sound-only source sends silence: the source stays live and its recording goes on, and the sound comes back by itself.
Live production rules
- A network port only for Dante (a PCIe or USB 3 gigabit adapter, chosen as the Network Interface of DVS). The port of the central computer also carries the site feeds and the NDI outputs (about 100 Mbit/s per receiver at 1080p30): when it's full, the clock of Dante arrives late and the sound clicks. Without a second port: a managed switch with QoS (DSCP 56 and 46 first).
- Turn off Energy Efficient Ethernet / Green Ethernet on the Dante port (driver settings of the network card) and on the switch: it's a known cause of Dante dropouts.
- High-performance power plan, no sleep.
- Before the service: Status > Sound (Dante) shows every sound out Playing, without dropouts.
Cluster
Sound outputs and the desk in the intercom run on the main computer only, like the tunnel. Each computer that can become main needs its own DVS license. Dante routes by device name: after a takeover, load the routing of the new main computer in Dante Controller (save it as a preset beforehand). Sound-only sources stay on the computer whose Dante pair they use.